How to Request a Fence Quote

A fence quote request is ready when each line specifies the intended job, dimensions, quantity, finish and destination. Attach the relevant drawing or sample, then show mounting, connection and packing requirements that affect acceptance. Relia can review each item against that information and ask for the missing detail before quoting.

Minimum request
Product or project line, quantity, units and delivery country
Useful attachment
The current drawing, sample photo or measured connection detail
Project fencing sample boards and steel mesh in a documentation workspace

A sample line list to adapt to your project

Use these examples as a starting point for recording your measured quantities. Add the measured fit, selected finish, delivery point and count for each line before requesting prices. Relia can quote the scope more precisely when line quantity, fitting and packing needs are easy to identify.

Write one complete line that can be approved. For a 50 × 100 mm V-bend panel listing, specify the selected wire, post type, finish, fitting counts and delivery destination on the same line. Attach the drawing revision and identify any checks you need recorded. List the gate or terminal assembly separately when its parts differ.

Example lineUse this basisAdd before requesting a quote
Temporary panel and fittings
Actual width and count plus separate feet, clamps, braces and any project approval
Permanent mesh assembly
50 × 100 mm V-bend panel with 3.0 mm example wire
Selected width and height, support sections, caps and clips
Custom steel grating
Overall size, clear span, bearing direction and approved design load
New installation
Send the layout and the conditions that determine gates, posts and clearances.
Existing-system replacement
Send a working reference part or a measured photo of the joint you want to keep.
Made-to-drawing steelwork
Attach the current drawing and mark the material, finish and any acceptance documentation.

A review sheet for a quote-ready enquiry

Check the parts that determine fit, matching hardware and the cost of receiving the order. Fill the fields you know and identify the decisions you want the quotation to cover.

Use the same units and drawing revision
A short release check for the buyer preparing a request
  1. Identity
    Put one item or site area on each line and provide a model, drawing or measured reference.
  2. Scope
    Give the sizes, finish, quantity and mating parts the price should cover.
  3. Acceptance
    Identify the measurement records, sample, installation drawing or packing evidence required for the project.
  4. Delivery
    Send the delivery country and receiving constraints and request the applicable packing and lead time in the quote.

Give the quote a drawing revision and one unit system

Write dimensions in your agreed unit and mark which value is finished height, outside frame width or installed centres. If you have a screened site or a retained base, call it out on the relevant line. Record the drawing revision in the subject or the line schedule so both sides work from the same document.

Temporary panel and removable foot beside an unmarked dimension drawing

Choose the information that matches the purchase

You can start with a sketch if you know the job. Add the fields that distinguish the real order before asking for a firm price. Start with the product-specific fields that determine fit and share the information still under review.

  • New siteMap ends, gates and the support arrangement.
  • ReplacementSend a face view, an end view and actual retained part measurements.
  • Stock orderSet the finish, pack, spares and configured dimensions by SKU.

Attach the connection and mounting details

Where a mesh panel meets an existing post or clip, include the cross-section and hole pattern. Draw each type of corner or end. The measured interface gives us a specific starting point for the review. Include close views of a retained mount or fitting and measurements from a clear datum.

Post and mesh contact details ready for a drawing review

A complete enquiry in three steps

A first message can be short. Use the product line as the common reference when sending the attachments. Check that the final attachment uses the same names and quantities as the request.

A quote brief for a new site, a replacement or a custom part
  1. Start with these inputsState the job and the required pieces

    List each panel or profile and its parts. For a new site, attach the layout. For a replacement, include a reference photo from the fitting side.

  2. Specify the orderGive quantities and a consistent unit system

    Use the current drawing revision, finish by item and delivery destination. Put quantities against the product they describe.

  3. Verify before releaseName the document that closes each open point

    Ask for a matching drawing, sample, material note or assembly evidence where relevant. Email drawings or photos with the same project reference.

Detailed checks for this order
  1. DescribeInclude product links or intended use and your destination.
  2. MeasureAttach dimensions, labelled photos or a drawing revision.
  3. RequestSpecify quantity, timing, finish and approval paperwork you need.

Let each scope retain its own acceptance data

A grating order needs its approved load and support arrangement. A basket purchase needs aperture and outside box dimensions. Give each its own fields even if both will ship to the same site. Set the acceptance information at the level of the product or site section it will verify.

A steel grating sample and basket mesh awaiting their separate quote details

Use the form or email your drawings

Use the native enquiry form for the introduction. Email large drawings or a parts list. After you receive an offer, use the order-check page for approvals and batch references. Add the project reference when you email drawings or continue the enquiry in the site form.

Include the destination and documents you need

Share the site and quantities in the form, or email the relevant drawings with the same project reference. Include the delivery destination and any required documents.

Project
Name, use and intended destination
Scope
Listed parts, quantities and finish
Evidence
Drawings, samples, inspection or project requirements
Qingdao Relia Industries Co., Ltd.Shuyuan Road, Qingdao, Shandong, China